Back to Blog
Tips & Care 2026-11-04 Over the Brick 2 views

How to Base Miniatures With Battlefields Deadland Tuft

How to Base Miniatures With Battlefields Deadland Tuft

A step-by-step guide to applying Battlefields Deadland Tuft to miniature bases, from prepping the base to gluing tufts with tweezers and sealing them for play.

Quick answer

Apply Battlefields Deadland Tuft after your base is fully painted and sealed: pick each tuft with tweezers, dip the root in a tiny dot of super glue, and press it onto the base. Work from large tufts to small ones so you can judge spacing before committing.

Why deadland tufts need a different approach

Deadland Tuft is designed to evoke a barren, deathly landscape rather than a lush meadow. That means placement matters more than volume: a few clusters read as sparse wasteland, while an even carpet of tufts looks like ordinary static grass. Use the three supplied sizes to build irregular clumps and leave bare ground visible between them.

Because the tufts are pre-made, you are not shaping them from loose flock. The trade-off is less control over individual strands, but far faster and more consistent results once you settle on a placement pattern.

When to skip tufts on a base

If your miniature is mounted on a display plinth or a base that will be handled heavily, tufts can snag or flatten over time. In that case, reserve them for larger scenic bases or areas protected by the model's feet and nearby rocks. For tournament armies that are packed and unpacked weekly, keep tufts low and sparse rather than tall and dense.

Steps for applying Deadland Tuft to a base

  1. Finish and seal the base first: Paint, texture, and varnish the base completely before adding any tuft. Tufts are added last so paint and wash do not mat the fibres. Common mistake: gluing tufts onto wet texture paint, which prevents a strong bond. If you plan to varnish the whole model later, use a brush-on varnish around the tufts rather than a heavy spray.
  2. Plan placement with the large tufts: Dry-fit the 12 large tufts first, using tweezers to set them on the base without glue. Group them in twos or threes near rocks, feet, or base edges to suggest neglected ground. Checkpoint: step back at arm's length; if the tufts look evenly spaced, rearrange them.
  3. Glue each tuft with a tiny dot of super glue: Apply a small dot of super glue to the base where the tuft root will sit, not to the tuft itself. Press the tuft down with tweezers for a few seconds. Common mistake: using too much glue, which wicks up the fibres and leaves a shiny patch. Keep a scrap base nearby to test glue quantity before touching the model.
  4. Fill gaps with medium and small tufts: Use the 35 medium tufts to bridge between large clusters, then the 30 small tufts to soften edges and add detail near the model's feet. Leave some bare base visible between clumps. Checkpoint: if you cannot see the base texture in at least a few spots, you have over-tufted.
  5. Trim any stray fibres and check the bond: Once the glue is fully cured, snip any tuft fibres that stick out unnaturally or cross onto the model's legs. Gently tug each tuft with tweezers; if it lifts, re-glue with a fresh dot. Common mistake: trimming before the glue cures, which pulls the tuft loose. Wait at least the glue manufacturer's recommended cure time before trimming or handling.

Product facts

  • Battlefields: Deadland Tuft: Battlefields Deadland Tuft contains 30 small, 35 medium, and 12 large tufts in three sizes. Having three sizes lets you vary clump scale across a squad so bases do not look stamped from the same mold.
    Battlefields: Deadland Tuft
    Battlefields: Deadland Tuft

Related Articles

Customer Service
Home
Products
Cart
Profile